广州合成钣金机械制造企业
扫描加微信
企业概况 产品分类 工程实例 新闻中心 客户留言 下载中心 招聘信息 加盟经销商 联系我们
恒利通序述
公司简介
公司资质
生产车间
制造理念
公司宗旨
售后服务
客户订货须知
产品安装须知
代理经销商
 
联系方式
地址: 东莞市东城同沙科技园等水岭新村一号
电话: 0769-22952927
  0769-22679193
传真: 0769-22662827
  0769-89032033
网址: www.htfan.com
邮箱: 576891724@qq.com
  您好!我是江先生,有什么可以帮到您!
 
售后服务热线
服务热线
 
  首页 产品安装须知
 
产品安装须知
风机安装前应检查机壳的叶轮是否在运输及搬运过程中损坏,风机必须安装在混凝土基础上或安装在钢架上,
机座要安装减振装置,出入风口要安装帆布管减振避免风机运行产生共振而影响使用效果。
安装时要注意检查连接部份有无松动,用手拨动叶轮与风壳间隙是否均匀,如发生相碰撞要进行修理后再安装。
如吊装须配吊装架及减震弹簧或橡胶减震垫用吊杆吊装。
风机的吸风管要大于出风管,误差不能大于10%,进风口要安装斗形变接口,用户必须按要求安装。
风机应安装平行,不平度不能超过2%。
风机安装完毕应检查风机内是否有杂物,并检查电动机皮带轮和风叶皮带轮两轮是否在同一水平线上。
风机配电时,2.2KW以上的电动机应安装△型接电的过载保护装置的起动器。
开机前应检查供电线路、开关及接线方法是否正确,接线柱接线是否安全牢固,确认安全才能开机。
电动机要注意防潮、防水,盖好电机防护罩以免烧坏电机。
传动主轴轴承每季度应用油枪注入3号轴承油脂或40号液体机油二次。
风机的蜗牛壳内不能积油(水)过多,应定期清理风轮及机体内部以免影响风机的正常运转。
因缺相、过载,电机入油(水)或电机外壳积尘造成电机损坏,错误保养造成风机主轴、风轮和不可抗拒自然
灾害损坏的都不属于本公司保修范围。
Before the installation, you should check whether the impeller of the chassis is damaged in the transportation
or handling. The fan must be installed on the concrete foundation or fixed on steel framework. An anti-vibration device must be fixed to the machine frame, and the wind outlet needs a canvas hose to reduce the vibration and avoid resonance vibration while running. The vibration will affect the effect of the fan.In installation, pay attention to checking whether the connecting parts are loose. Pull the impeller and fan
shell to see if the clearance is even. If there is any collision, it needs repairing before installation.
If hoisting installation is used, a hoisting frame must be equipped as well as vibration damping spring or rubber bumper for vibration damping and the steeve for hoisting.
 The air sucking pipe of the fan should be bigger than the air outlet pipe, with the tolerance less than 10%.
The air inlet needs a hopper-shaped mouthpiece. Users must install the fan as required.
The fan should be installed evenly, and the non-evenness cannot exceed 2%.
After installation, check whether there are any sundries inside the fan. Also check whether the motor belt
wheel and the impeller belt wheel are at the same horizontal level.
When supplying power to the fan, you should install a starter as the overloading protection  device for a
delta power connection in case of 2.2kw electromotor.
Before turning on the fan, you should check whether the power supply, the switch and wire connections are correct, and the terminal wiring is safe and secured. Turn on the machine only after ensuring safety.
The electromotor needs moisture-proof and water-proof. Keep the electromotor covered lest the machine burnt out.
Convey main bearing should be injected No.3 bearing grease or No40 liquid mechine grease twice each quarter
There should not exist too much water in the snail hull.and the wind wheels and inside of the machine should
be cleared up regurally.lacking of parts,overload and water in the machine or dusty on the hull those factors
cause damaged. Maintaining in wrong way or the main bearing of wind machine , wind wheel and irresisible
natural disasters are not included.
 

 

全国免费电话:400 889 0881
Copyright ©2010-2015 云浮市恒利通风机有限公司 >> 管理员登录 流量统计: 网站维护:13922983965 卢生 粤ICP备08002065号-1
关闭
客 服 服务
点击这里给我发消息
客服一
点击这里给我发消息
客服二
点击这里给我发消息
客服三